8,367
edits
Changes
→How to use RKDevTool to burn Linux image into eMMC
# The development board reserves the expansion interface of the eMMC module. Before programming the system to the eMMC, you first need to purchase an eMMC module that matches the eMMC interface of the development board. Then install the eMMC module to the development board. The location of the eMMC interface is as follows：
::[[File:plus5-img78.png|307x141px]]
<ol start="2" style="list-style-type: decimal;">
<li>It is also necessary to prepare a data cable with a good quality Type-C interface</li>
[[File:plus5-img21.png|150x152px]]
</ol>
<ol start="3" style="list-style-type: decimal;">
<div class="figure">
[[File:plus5-img79.png|408x99px|c40e71d1a66216e12b3b4297138f749]]
</div></ol>
<div class="figure">
[[File:plus5-img80.png|337x138px|2feec28318eaa60c0514000158b889a]]
</div></ol>
<div class="figure">
[[File:plus5-img73.png|340x108px|e6986fc9c8fc078e8cb6a9c39b76fb8]]
</div>
<li>Then use decompression software to decompress '''DriverAssitant_v5.12.zip''', and then find the '''DriverInstall.exe''' executable file in the decompressed folder and open it</li>
[[File:plus5-img47.png|496x146px]]
</ol>
<ol start="6" style="list-style-type: decimal;">
<li>Click the "'''Driver Installation'''" button</li>
[[File:plus5-img48.png|284x149px]]
</ol>
<ol start="2" style="list-style-type: lower-alpha;">
<li>After waiting for a period of time, a pop-up window will prompt "'''driver installed successfully'''", and then click the "'''OK'''" button.</li>
[[File:plus5-img49.png|296x154px]]
</ol>
</li></ol>
<li>Then decompress RKDevTool_Release_v3.15.zip, this software does not need to be installed, just find '''RKDevTool''' in the decompressed folder and open it</li>
[[File:plus5-img50.png|484x143px]]
</ol>
<ol start="8" style="list-style-type: decimal;">
<li>After opening the '''RKDevTool''' burning tool, because the computer has not been connected to the development board through the Type-C cable at this time, the lower left corner will prompt "'''No device found'''"</li>
[[File:plus5-img51.png|442x208px]]
</ol>
<ol start="9" style="list-style-type: decimal;">
<div class="figure">
[[File:plus5-img52.png|403x114px|C:\Users\orangepi\Desktop\用户手册插图\Pi5 Plus\未标题-2.jpg未标题-2]]
</div></ol>
<li><p>Then press and hold the MaskROM button on the development board, the position of the MaskROM button on the development board is shown in the figure below:</p></li>
[[File:plus5-img53.png|418x94px]]
</ol>
<ol start="4" style="list-style-type: lower-alpha;">
<li>Then connect the power supply of the Type-C interface to the development board, and power on, and then release the MaskROM button</li>
[[File:plus5-img54.png|407x124px]]
</ol>
<ol start="5" style="list-style-type: lower-alpha;">
<li>If the previous steps are successful, the development board will enter the '''MASKROM''' mode at this time, and the interface of the burning tool will prompt "'''found a MASKROM device'''"</li>
[[File:plus5-img55.png|457x215px]]
</ol>
<ol start="6" style="list-style-type: lower-alpha;">
<li>Then place the mouse cursor in the area below</li>
[[File:plus5-img81.png|458x215px]]
</ol>
<ol start="7" style="list-style-type: lower-alpha;">
<li>Then click the right mouse button and the selection interface shown in the figure below will pop up</li>
[[File:plus5-img57.png|460x216px]]
</ol>
<ol start="8" style="list-style-type: lower-alpha;">
