Linux Distributions for Orange PI H3 boards

loboris

Orangepi2mini replied at 2015-10-1 21:23
Hello everyone,

Have anyone get DS18B20 (Dallas one wire thermometer sensor) to work with Orange pi ...

For 1wire to work you must load wire, w1-sunxi and w1-gpio modules. Also 1w must be added un fex and some kernel sources changed and addedd.
I've did it all, all the modules loads fine, but DS18B20 is not detected.

loboris

Vinion replied at 2015-10-1 18:28
Can you make a  script.bin.OPI-XXXX for 800x480 ???

Thank you for your work

For 800x480 resolution to work, the kernel sorces must be modified to.
I have the working kernel and script.bin for 800x480, but if you plan to use it with small 5" or 7" TFT monitors, it still doesn'w work properly.
See this thread.

loboris

About problems with USB wifi adapters, I'll get some next week and I'll try to make at least one of them work.

Orangepi2mini

loboris replied at 2015-10-2 16:59
For 1wire to work you must load wire, w1-sunxi and w1-gpio modules. Also 1w must be added un fex a ...

Dear Loboris,

First of all, thank you for your job and great support!
1) Yes, I enabled following kernel modules:
<*> Dallas's 1-wire support  --->     
1-wire Bus Masters  --->         <*> GPIO 1-wire busmaster     
1-wire Slaves  --->                 <*> Thermal family implementation
2) Recompiled kernel
3) Edited script.fex:
[w1_para]
w1_used = 1
w1_pin = port:PA10<1><default><default><default> (PA10 not PB10, because H3 chip doesn't have PB port bank. Or am I wrong?)
4) Convert FEX to BIN
5) Then loaded w1_therm module, but can' t load w1-gpio module
6) And yes, DS18B20 is not detected too.

syed.iddi

The latest packages most of them except raspbian doesn't detect the ethernet connection..

Getting this error

Creating object for path '/org/freedesktop/NetworkManager/ActiveConnection/0' failed in libnm-glib

syed.iddi

loboris replied at 2015-10-1 19:21
copy the downloaded firmware.tar.gz to /lib
-rw-rw-r-- 1 boris boris 8192 Lis  1 10:03 rt2561.bin
- ...

All the linux images doesn't detect ethernet.
Getting this msg,

Creating object for path '/org/freedesktop/NetworkManager/ActiveConnection/0' failed in libnm-glib.


any idea how to fix it?

Fabrixio1

Thanks @loboris for the kernel sources, The wifi AP6212 works now.

I have this error yet:

Oct  3 06:25:31 localhost kernel: [ 8000.148942] [cpu_freq] ERR:set cpu frequency to 1200MHz failed!
Oct  3 06:28:25 localhost kernel: [ 8171.966410] [ARISC ERROR] :message process error
Oct  3 06:28:25 localhost kernel: [ 8171.971747] [ARISC ERROR] :message addr   : f004b840
Oct  3 06:28:25 localhost kernel: [ 8171.977361] [ARISC ERROR] :message state  : 5
Oct  3 06:28:25 localhost kernel: [ 8171.982232] [ARISC ERROR] :message attr   : 2
Oct  3 06:28:25 localhost kernel: [ 8171.987167] [ARISC ERROR] :message type   : 30
Oct  3 06:28:25 localhost kernel: [ 8171.992113] [ARISC ERROR] :message result : ff
Oct  3 06:28:25 localhost kernel: [ 8171.997037] [ARISC WARING] :callback not install

Some idea how to correct them?

Thanks.

jacer

loboris replied at 2015-9-30 16:05
Try tu use the latest pyhoca-gui (0.5.0) or x2go client.
I think that i've tried that MT7601 sourc ...

The mate image is working with this x2go client. Care to make this wifi dongle workig? It is working with rasperberry pi.Bus 004 Device 002: ID 0bda:8176 Realtek Semiconductor Corp. RTL8188CUS 802.11n WLAN Adapter

lukish

loboris replied at 2015-10-1 02:07
The driver for CH341 USB->Serial is in the kernel sources, I've compiled it and I'll upload it tom ...

loboris, what's the progress with the module?

on4top

Would love to have  script.bin for  1440×900 & 1680×1050 resolutions  ( older 16:10 monitor )

Also usb_cdc support in kernel ..would be nice ..