Openelec Build for OPI PC and 2 now with HW decoding

tomkowski · Published in 2016-2-21 15:35:25

After burning the .img lan and USB did not work. When I updated by .tar (copied to "Update" foler) - everything worked OK.

bif1972 · Published in 2016-2-21 17:24:21

Edited by bif1972 at 2016-2-21 17:32

tomkowski replied at 2016-2-21 15:35
After burning the .img lan and USB did not work. When I updated by .tar (copied to "Update" foler) - ...

Hi
For me it does not work USB and LAN (I have OPI+). Could I ask for a step-by-step what to do?
Możesz pisać po polsku

jernej · Published in 2016-2-21 17:29:02

Please keep writing in english so everyone will understand.

jeevasv · Published in 2016-2-21 18:20:02

I understood the problem. For some reason the below command that i used is failing to clear uboot properly.

sudo PROJECT=H3 DEVICE=OPi2 ARCH=arm ./scripts/clean uboot

manually deleting the u-boot in build folder resolved the problem.

Uploading the new Builds now.

nightflasher · Published in 2016-2-21 18:58:09

as i'm using my OPiPC as my mediacenter in bedroom, i found some strange issues:
- i'm online...but cannot access ssh/web
- i can connect usb devices and the were recognized
- wifi works and ethernet works
- still no chance to get in touch with my device without keyboard
- reboot doesn't help
- manual ip settings doesn't help
WTF?

well0ne · Published in 2016-2-21 19:47:55

nightflasher replied at 2016-2-21 18:58
as i'm using my OPiPC as my mediacenter in bedroom, i found some strange issues:
- i'm online...but ...

well, webinterface should be available by stock.
ssh has to be enabled in the KERNEL CMDLINE (boot.scr), this worked atleast for me.
try to ping it, maybe something is blocking connections

nightflasher · Published in 2016-2-21 21:25:13

Edited by nightflasher at 2016-2-21 21:28

i'vetried everything, now i found a setting on my router which used to be switched on and already was => wifi devices can communicate. it's on by default and it worked fine with my retropie powered RPi2 and my fritz.repeater...i've toggeld this option and now it works, don't know if that last. but it's suspicious, the orange pi pc was the only not communicating device...i have an eye on that ;-)
but still have no acceptable resolution...about 3m away from my 22" screen, you see this poor 640x480...

jeevasv · Published in 2016-2-22 08:16:06

Uploaded the new builds which should hopefully correct the script.bin nuance present in some platforms at the same location as before.

Please test and verify.

Jernej, Probably you can update the date again to 21-02-2016

c0013r · Published in 2016-2-22 16:19:21

new driver IR:
I have last build tuned file lircd.conf with my setting NEC IR remote control(manual 1 page this tread)
I copy lircd.conf to /storage , autostart.sh /storage/.config, add permission, reboot, in january build work - OK
But latest february build no work, what i doing wrong?

jeevasv · Published in 2016-2-22 19:40:42

c0013r replied at 2016-2-22 16:19
new driver IR:
I have last build tuned file lircd.conf with my setting NEC IR remote control(manual ...

For new builds you need to repeat the IR remote recording using the new method mentioned in the FAQ or use the method mentioned in the below thread:

http://www.orangepi.online/orangepi ... &extra=page%3D1