8,367
edits
Changes
no edit summary
<li>Then decompress '''RKDevTool_Release_v2.96.zipRKDevTool_Release_v3.15.zip''', this software does not need to be installed, just find '''RKDevTool''' in the decompressed folder and open it</li>
[[File:media/image50plus5-img50.png|575x170px]]
</ol>
<ol start="9" style="list-style-type: decimal;">
<li>After opening the '''RKDevTool''' burning tool, because the computer has not been connected to the development board through the Type-C cable at this time, the lower left corner will prompt "'''No device found'''"</li>
[[File:media/image51plus5-img51.png|402x189px]]
</ol>
<ol start="10" style="list-style-type: decimal;">
<div class="figure">
[[File:media/image52.jpeg|400x113px|C:\Users\orangepi\Desktop\用户手册插图\Pi5 Plus\未标题plus5-2img52.jpg未标题-2png]]
</div></ol>
<li><p>Then press and hold the MaskROM button on the development board, the position of the MaskROM button on the development board is shown in the figure below：</p></li>
[[File:media/image53plus5-img53.png|382x93px]]
</ol>
<ol start="4" style="list-style-type: lower-alpha;">
<li>Finally, connect the power supply of the Type-C interface to the development board, and power on, and then release the MaskROM button. The location of the Type-C power interface is as follows：</li>
[[File:media/image54plus5-img54.png|404x123px]]
</ol>
<ol start="5" style="list-style-type: lower-alpha;">
<li>If the previous steps are successful, the development board will enter the '''MASKROM''' mode at this time, and the interface of the burning tool will prompt "'''found a MASKROM device'''"</li>
[[File:media/image55plus5-img55.png|457x215px]]
</ol>
<ol start="6" style="list-style-type: lower-alpha;">
<div class="figure">
[[File:media/image56plus5-img56.png|455x216px|图片1]]
</div></ol>
<li>Then click the right mouse button and the selection interface shown in the figure below will pop up</li>
[[File:media/image57plus5-img57.png|453x213px]]
</ol>
<ol start="8" style="list-style-type: lower-alpha;">
<li>Then select the '''import configuration''' option</li>
[[File:media/image58plus5-img58.png|458x215px]]
</ol>
<ol style="list-style-type: lower-roman;">
<li>Then select the '''rk3588_linux_tfcard.cfg''' configuration file in the '''MiniLoader''' folder downloaded earlier, and click '''Open'''</li>
[[File:media/image59plus5-img59.png|483x227px]]
</ol>
<ol start="10" style="list-style-type: lower-alpha;">
<li>Then click '''OK'''</li>
[[File:media/image60plus5-img60.png|483x227px]]
</ol>
<ol start="11" style="list-style-type: lower-alpha;">
<li>Then click the position shown in the figure below</li>
[[File:media/image61plus5-img61.png|486x228px]]
</ol>
<ol start="12" style="list-style-type: lower-alpha;">
<li>Then select '''MiniLoaderAll.bin''' in the '''MiniLoader''' folder downloaded earlier, and then click to '''open'''</li>
[[File:media/image62plus5-img62.png|492x231px]]
</ol>
<ol start="13" style="list-style-type: lower-alpha;">
<li>Then click the position shown in the figure below</li>
[[File:media/image63plus5-img63.png|493x232px]]
</ol>
<ol start="14" style="list-style-type: lower-alpha;">
|}
[[File:media/image64plus5-img64.png|499x234px]]
</ol>
<ol start="15" style="list-style-type: lower-alpha;">
<li>Then please check the '''option to force writing by address'''</li>
[[File:media/image65plus5-img65.png|489x230px]]
</ol>
<ol start="16" style="list-style-type: lower-alpha;">
<li>Then click the execute button to start burning the linux image to the tf card of the development board</li>
[[File:media/image66plus5-img66.png|492x231px]]
</ol>
<ol start="17" style="list-style-type: lower-alpha;">
<div class="figure">
[[File:media/image67plus5-img67.png|492x231px|%O4~FPPAT$0RH{3S~CGJ@@Q(1)]]
</div></ol>
<div class="figure">
[[File:media/image68plus5-img68.png|209x228px|选区_199]]
</div></ol>
<li>Then click "'''Format'''", a warning box will pop up before formatting, and formatting will start after selecting "'''Yes (Y)'''"</li>
[[File:media/image69plus5-img69.png|304x147px]]
</ol>
<ol start="5" style="list-style-type: lower-alpha;">
<li>After formatting the TF card, the message shown in the figure below will pop up, click OK</li>
[[File:media/image70plus5-img70.png|186x149px]]</ol>
</li></ol>
<ol start="4" style="list-style-type: decimal;">
<big>'''Note, if you download the OpenWRT image, you will see the following two types of images in the download link of the OpenWRT image, please download the image file in the "TF card, eMMC and NVME SSD boot image" folder.'''</big>
[[File:media/image34plus5-img34.png|309x98px]]
|}
</ol>
<div class="figure">
[[File:media/image71plus5-img71.png|297x206px|C:\Users\orangepi\Desktop\用户手册插图\Pi5 Plus\a8fda8737c5b0b3b38fbb75ef68acfc.pnga8fda8737c5b0b3b38fbb75ef68acfc]]
</div></ol>
<li>After entering the balenaEtcher download page, click the green download button to jump to the place where the software is downloaded</li>
[[File:media/image35plus5-img35.png|575x276px]]
</ol>
<ol start="5" style="list-style-type: decimal;">
<li>Then choose to download the Linux version of the software</li>
[[File:media/image72plus5-img72.png|575x218px]]
</ol>
<ol start="6" style="list-style-type: decimal;">
<div class="figure">
[[File:media/image73plus5-img73.png|275x87px|e6986fc9c8fc078e8cb6a9c39b76fb8]]
</div>